DC Circuits 1st Edition by Davis, Chad.
Table of Contents
▪Module 1 – The Basics of DC Circuits with Resistors
Section 1.1 – Introduction and Basic Definitions
Section 1.1.1 – Charge vs Current
Section 1.1.2 – Resistance Calculations – (Resistance explained in more detail in section 1.1.3)
Section 1.1.3 – Ohm’s Law: Voltage, Current, Resistance, and Conductance
Section 1.1.4 – Power and Energy
Section 1.2 – Combining Resistors in Parallel or Series
Section 1.3 – Kirchhoff’s Voltage Law (KVL) and Voltage Divider Rule (VDR)
Section 1.4 – Kirchhoff’s Current Law (KCL) and Current Divider Rule (CDR)
Module 1 – Equation List
Module 2 – Advanced Topics for DC Circuits with Resistors
Section 2.1 – Source Transformations: Thevenin and Norton Form
Section 2.2 – Approximate Source Transformations: Adding a virtual resistor
Section 2.2.1 – Voltage Source Approximate Transformation
Section 2.2.2 – Current Source Approximate Transformation
Section 2.3 – Mesh Matrix Analysis and traditional loop analysis methods
Section 2.4 – Nodal Matrix Analysis and traditional Nodal Analysis
Section 2.5 – Superposition: Solving a circuit by including only one source at a time
Section 2.6 – Thevenin and Norton Equivalent Circuits
▪Module 3 – DC Circuits with Resistors, Capacitors, and Inductors
Section 3.1 – Background for Capacitors
Section 3.2 – Background for Inductors
Section 3.3 – Combining Inductors in Parallel and/or Series
Section 3.4 – Combining Capacitors in Parallel and/or Series
Section 3.5 – DC Transient Analysis with RC and RL Circuits
Section 3.5.1 – Single Loop RL and RC Charging (Store) Circuits
Section 3.5.2 – Single Loop RL and RC Discharging (Release) Circuits
Section 3.6 – DC Steady State Analysis with RC, RL, and RLC Circuits
Section 3.7 – Introduction to Passive Filters
Module 3 – Equation List
▪References and Links
▪Appendix – Dependent Sources and Laplace Transform Examples
Preface by Davis, Chad:
This book covers Direct Current (DC) circuit theory and is broken up into three modules. Module 1 covers the basics for circuits that include DC sources (voltage or current) and resistors. Even though Module 1 is not very difficult, it forms the foundation for more complicated topics in Module 2 and 3 so it is important to have a firm grasp of all Module 1 topics before moving on. Module 2 covers more difficult problem solving techniques for circuits that include only DC sources and resistors. Capacitors and inductors are introduced in Module 3 and these non-linear reactive components are analyzed in circuits with DC sources in both the transient and steady state. There are two follow-on books in this 3- part series: AC Circuits (published in 2017) and Electromechanical Systems (published in 2018).
The circuits in this book are created with a user friendly circuit drawing and simulation tool called Multisim. Creating new circuits and simulating them to verify your calculations are correct is a good way to hone your skills. While it is a luxury to have a program like Multisim that you can use to check your answers, a word of caution is in order. Sometimes people will become so dependent on Multisim that they have no confidence that they can get the correct answer without it. Additionally, learning to solve the circuit problems helps prepare you for the variety of different problems you will solve in the future. By learning how to solve new types of problems you become a better problem solver, which is what the world desperately needs. Engineers that have become adept at solving complicated problems in many different areas are desperately needed to help solve the challenges we face. So focus on learning to become a better problem solver instead of becoming a master in simulating circuits in Multisim.
One goal of this book is to provide practical information so that you are better equipped to put circuit theory into practice. The picture on the cover of this book shows an example of the early stages of a student’s attempt to build the circuitry for an analog robot. It is my hope that as you master circuit theory you will also be empowered to build something of your own with the knowledge you gain. The book is written so that enough practical information is covered to explain the concepts, but tries to avoid going into too many tangents that result in numerous pages being skipped over by the reader. When I felt the temptation to depart from the main point, I provided links to additional information. Many of the links come from allaboutcircuits.com, which is a very good open educational resource. The primary goal of this book is to explain how to solve a variety of DC circuit problems in a more efficient and simple manner than you normally find in circuits books. Over the years I have developed many shortcuts, solving methods, and procedures that greatly simplify the most difficult circuit problems.
When I took my first introductory circuit course, I was overwhelmed by all of the confusing problem solving techniques and quickly got behind and buried in confusion. I still have nightmares about the terms super-node and super-mesh! I promise you will not see those horrible methods covered in this book, but instead easier methods that don’t end in confusion and madness will be shown. After my bad experiences trying to understand circuits in college, I made it my mission to learn circuits on my own and figure out ways to make the problems easier to solve. I was fortunate to have some amazing professors along the way that helped me in my quest for knowledge. I am especially grateful to a legendary OU professor named John Fagan, who served as my mentor and advisor during my graduate studies and inspired me to pursue a career in academia. He first introduced the idea of the “Matrix Method” to me and taught me the importance of hands-on projects and experiential learning in engineering education.
⏩Author: Davis, Chad
⏩Puplication Date: 2016-08-08
⏩Size: 7.60 MB
Download DC Circuits 1st Edition by Davis, Chad in pdf format for free.